New Angle roll benders with 4 rolls

4 roll bender - Angle roll

Metfab has just added new roll benders to its catalog. These are three new hydraulic angle rolls with 4 rollers.

Theses angle rolls have a top roll, a bottom and two lateral rolls. The two side rolls have a wide distance between them to allow easier bending of large pieces of metal. The roll benders with 4 rolls also make it possible to bend smaller diameters compared to angle roll benders with 3 rolls. The 4R 90 and 110 bending machines have three hydraulically driven rolls, thus reducing the size of the flat on the edge. Theses three new machines are waiting to join your shop!

4 roll bender 4R 70Angle roll bender 4R 70

  • Motor: 3 kW
  • 2 hydraulic rolls (top and bottom)
  • Rolls diameter: 7.87 inches
  • Shafts diameter: 2.76 inches

 

4 roll bender 4R 90Angle roll bender 4R 90

  • Motor 5.5 kW
  • 3 hydraulic rolls
  • Top roll idle
  • Rolls diameter: 10.23 inches
  • Shafts diameter: 3.54 inches

 

4 roll bender 4R 110Angle roll bender 4R 110

  • Motor 7.5 kW
  • 3 hydraulic rolls
  • Top roll idle
  • Rolls diameter 12.60 inches
  • Shafts diameter: 4.33 inches

 

Bending capacity of the Angle Rolls 4 rolls 

  4R 70 4R 90 4R 110  
No. Profile Type Size Min. Diam Size Min. Diam Size Min. Diam Notes
1 Flat Bar 2,36 x 0,39 19,69 3,94 x 0,79 78,74 3,94 x 0,79 31,50 Standard Rolls
0,79 x 0,2 9,84 3,15 x 0,79 31,50 1,18 x 0,39 15,75
    1,18 x 0,39 11,81    
2 Flat Bar 3,15 x 0,79 19,69 4,92 x 0,98 23,62 7,87 x 1,18 47,24 Standard Rolls
1,97 x 0,2 9,84 2,36 x 0,2 11,81 6,3 x 1,38 31,50
        3,15 x 0,2 15,75
3 Square Bar 1,26 x 1,26 15,75 1,77 x 1,77 19,69 2,36 x 2,36 29,53 Standard Rolls
0,47 x 0,47 9,84 0,59 x 0,59 14,96 0,59 x 0,59 15,75
4 Round Bar 1,38 13,78 1,97 19,69 2,95 31,50 Optional Rolls
0,39 9,84 0,59 14,96 0,59 17,72
5 Tube 2,36 x 0,08 23,62 3,94 x 0,1 47,24 4,92 x 0,1 55,12 Optional Rolls
0,59 x 0,06 7,87 0,59 x 0,04 14,96 0,59 x 0,04 17,72
6 Pipe 2 x 0,15 15,75 3 x 0,22 31,50 4 x 0,24 39,37 Optional Rolls
1/2 x 0,11 7,87 1/2 x 0,11 14,96 1/2 x 0,11 17,72
7 Rectangular Tube 1,97 x 0,98 x 0,12 17,72 3,15 x 0,98 x 0,12 31,50 3,94 x 1,57 x 0,16 51,18 Optional Rolls
0,79 x 0,59 x 0,08 9,84 0,98 x 0,59 x 0,08 13,78 0,98 x 0,59 x 0,08 17,72
8 Square Tube 1,77 x 0,12 23,62 2,76 x 0,12 51,18 3,15 x 0,2 59,06 Optional Rolls
0,79 x 0,08 11,81 0,98 x 0,08 15,75 0,98 x 0,08 17,72
9 Steel Angle 2,36 x 2,36 x 0,24 25,59 3,15 x 3,15 x 0,31 31,50 3,94 x 3,94 x 0,47 39,37 Optional Rolls
1,18 x 1,18 x 0,16 13,78 1,18 x 1,18 x 0,12 17,72 1,57 x 1.57 x 0,16 27,56
10 Steel Angle 1,97 x 1,97 x 0,2 21,65 2,76 x 2,76 x 0,28 27,56 3,94 x 3,94 x 0,39 39,37 Optional Rolls
1,18 x 1,18 x 0,16 13,78 1,18 x 1,18 x 0,12 17,72 1,57 x 1,57 x 0,16 21,65
11 Steel Tee Bar 2,36 x 0,28 21,65 3,15 x 0,35 31,50 3,94 x 0,43 39,37 Standard Rolls
0,79 x 0,12 9,84 0,98 x 0,14 11,02 1,18 x 0,16 15,75
12 Steel Tee Bar 1,97 x 0,24 19,69 2,76 x 0,31 31,50 3,54 x 0,39 39,37 Optional Rolls
0,79 x 0,12 9,84 0,98 x 0,14 11,02 1,18 x 0,16 15,75
13 Steel Tee Bar 2,36 x 0,28 19,69 3,15 x 0,35 31,50 3,94 x 0,43 39,37 Optional Rolls
0,79 x 0,12 9,84 1,18 x 0,16 11,81 1,18 x 0,16 15,75
14 U-Channel UPN 80 23,62 UPN 140 62,99 UPN 180 35,43 Standard Rolls**
UPN 30 9,84 UPN 120 35,43 UPN 30 15,75
    UPN 100 23,62 0,00 0,00
15 U-Channel UPN 65 23,62 UPN 140 62,99 UPN 180 39,37 Standard Rolls**
UPN 30 9,84 UPN 120 39,37 UPN 30 15,75
    UPN 100 31,50    
16 I-Beam IPN 80 23,62 IPN 120 23,62 IPN 180 39,37 Standard Rolls**
    IPN 80 15,75 IPN 80 15,75

* Sizes are in inch
** A special washer can be necessary

Related posts:

Leave a Reply

Your email address will not be published. Required fields are marked *